Current position > News detail
『Magnetic Flow Meter Manufacturers: Sourcing Global Industrial Induction Sensor Brands』Related information(clamp on meter|electromagnetic meter|venturi meterrotameter|orifice meter|ultrasonic flow meter|mass flow meter|coriolis mass flow meter|coriolis flow meter|magnetic flow meter|magmeter flow meter|magflow flow meter|mag meter flow meter|electromagnetic flow meter|vortex flow meter|turbine flow meter|thermal mass flow meter|thermal flow meter|rotameter flow meter)
Magnetic Flow Meter Manufacturers: Sourcing Global Industrial Induction Sensor Brands
Quick Answer: When sourcing magnetic flow meter manufacturers, focus on the induction sensor assembly, liner material, electrode type, and signal output compatibility. Silver Automation Instruments produces magnetic flow meters with your choice of rubber, PTFE, or PFA liners and electrodes in 316L, Hastelloy, titanium, or tantalum. Our meters come with 4-20 mA HART, pulse, or RS485 Modbus and we export to over 80 countries including the Philippines, UAE, Mexico, Nigeria, and Indonesia.
Magnetic flow meters work on electromagnetic induction, the Faraday law. A magnetic field is generated by coils, and when a conductive liquid flows, a voltage is induced. Two electrodes pick up this signal and convert it to flow rate. That is why the induction sensor (coil and electrode) matters more than the transmitter brand. Some low-cost suppliers use coils with poor insulation that short in humid conditions. We have seen this cause signal drop in Thailand sugar mills and a Colombian water plant. Silver Instruments uses Class H magnet wire and vacuum pressure impregnation so the coil resists moisture and vibration. We also offer electrode cleaning circuits for fluids that coat, such as sludge or latex.
Our standard liner is hard rubber for water and wastewater. For chemicals, we use PTFE or PFA which handles temperatures up to 180 °C. In a recent project for a chemical plant in Saudi Arabia, we supplied DN50 PTFE-lined magmeters with platinum-iridium electrodes for hydrochloric acid at 85 °C and 6 bar. The customer had previously used a brand-name European meter but the lead time was 12 weeks. We delivered in 3 weeks.
Communication Protocols and Field Integration
Most of our magnetic flow meters support 4-20 mA with HART 7 as standard. You can also order Modbus RTU over RS485, Profibus DP, or a simple pulse output for batching. If your SCADA system requires Foundation Fieldbus, we can supply that too but it adds 2 weeks. The typical accuracy is 0.5% of reading for velocities above 0.5 m/s and 0.2% is optional with factory calibration certificate.
Certifications for Global Markets
For hazardous areas, we offer ATEX Zone 1 and 2 explosion-proof enclosures (Ex d) and IECEx certified sensors. We al
Frequently Asked Questions About Magnetic Flow Meter Manufacturers
What is the minimum fluid conductivity for a magnetic flow meter?
The general rule is above 5 µS/cm. Demineralized water and some solvents fall below this and need a special low-conductivity magmeter with enhanced amplifier. Silver Instruments can measure down to 0.05 µS/cm with advanced digital signal processing. If you are measuring deionized water or alcohols, mention it in your RFQ.
Can you supply insertion magnetic flow meters for large pipe sizes?
Yes. We make hot-tap insertion magmeters for pipes from DN300 up to DN3000. These are popular for main water distribution lines in cities like Jakarta and Lima because you do not need to cut the pipe. The sensor has two electrodes and a verification function.
Do your meters work with battery power for remote sites?
We offer a battery-powered magnetic flow meter with an integrated data logger. It runs on two D-cell lithium batteries for up to 2 years and stores 500,000 data points. It is used in irrigation canals in rural Australia and wellhead monitoring in Africa.
What lead time can we expect for custom liners?
Standard rubber or PTFE lined meters in common sizes (DN25 to DN300) ship in 5 to 7 working days. Special electrodes and PFA lining add about 10 days. We keep 316L and Hastelloy electrodes in stock.
Can we get a sample unit for evaluation?
Yes, we can ship one evaluation unit at a discounted price. A water cooperative in Guatemala tested a DN100 rubber-lined magmeter for 2 months before ordering 40 units. Send us your application details and we will prepare a proforma invoice.
To get a quote, email [email protected] with your pipe size (DN), fluid name, temperature (°C), pressure (bar), and required liner and electrode material. Our engineering team will reply within one business day. You can also call +86-25-68650347 or message us on WhatsApp +86-25-52155837 or WeChat +86 15365082610. Visit flow-meter.com.au to browse the full magnetic flow meter range.